ZyXEL Communications U-1496 series Spezifikationen PDF herunterladen (Seite 13)

INSTALLATION AE/LZB 119 1889 R1A

Programming Cable

Serial COM Port

J4 J3

RPM 113 2514

Personal Computer

IBM-Compatable

Figure 4 - SIM Programming Setup

2. Power Up SIM: Make sure that the power switch

on the front of the SIM shelf is turned on.

3. Check SIM Display: Verify that the SIM is

alternately displaying a time and date (correct

values for time and date are not important). Other

information may also be alternately displayed. If a

time and date are not displayed, a failure in the

SIM is indicated and this programming procedure

should be aborted.

System Manager Communications

If customer-specific values for the SIM Personality are

not available in the factory, a generic personality is installed

for test purposes. Customer-specific values for the

following parameters must be programmed into the SIM

Personality before the SIM will be able to communicate with

the System Manager:

•

Site ID

•

Site Name (optional)

•

Site Password

•

Modem Type

•

Telephone Number (dialup modem type only)

Use the following procedure to program these

parameters in the SIM Personality:

1. Press

Ctrl + E

to get the SIM to echo the typed

characters, so that you will be able to see (on the

screen of the PC or terminal) what you type.

2. Type

set∧∧siteP,siteID∧∧BXx

(replacing Xx with the

Site ID - up to 3 integers), and press the

Enter

key.

3. Type

set∧∧siteP,siteName∧∧“Xx”

(replacing Xx

with the Site Name - up to 8 characters), and press

the

Enter

key. (Quotation marks are required.)

4. Type

set∧∧siteP,password∧∧“Xx”

(replacing Xx

with the Site Password - add spaces at end for a

total of 12 characters), and press the

Enter

key.

(Quotation marks are required.)

5. Type

run∧∧siteP,verifyAndLoad∧∧(∧∧)∧∧

and press

the

Enter

key. The SIM should respond by

displaying the word OK. If the word OK is not

displayed, a failure in the SIM is indicated and this

programming procedure should be aborted.

6. Type

set∧∧scc4P,modemType∧∧BX

(replacing X

with a number listed below), and press the

Enter

key. Use 0 for direct connections between the SIM

and the System Manager (such as RS-232 or T1).

X Modem Type

0 No Modem

1 Transparent

5 ZyXEL 2-wire leased line

6 ZyXEL 4-wire leased line

7 ZyXEL Dialup line

7. (Required for dialup modem type only.) Type

set∧∧scc4P,phoneNumber∧∧“Xx”

(replacing Xx

with the phone number of the System Manager - up

to 32 integers), and press the

Enter

key.

(Quotation marks are required.)

8. Type

set∧∧scc4P,protocol∧∧B2

and press the

Enter

key to set up the SIM’s scc4 port to run the System

Manager protocol.

9. Type

set∧∧scc4P,baudRate∧∧LX

(replacing X with

the baud rate of the System Manager interface), and

press the

Enter

key. The SIM presently supports

baud rates to the System Manager of 9600 and

19200 (default), but the System Manager is

generally set to 9600. If a direct connection is used

between the SIM and the System Manager, both

must be set to the same baud rate.

10. Type

run∧∧scc4P,verifyAndLoad∧∧(∧∧)∧∧

and press

the

Enter

key. The SIM should respond after

about 3 seconds by displaying the word OK. If the

word OK is not displayed, a failure in the SIM is

indicated and this programming procedure should

be aborted.

11. Type

run∧∧PersonalityObject,programFlash∧∧(∧∧)∧∧

and

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 33 34

Kommentare zu diesen Handbüchern

Keine Kommentare

ZyXEL Communications U-1496 series Spezifikationen Seite 13

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung ZyXEL Communications U-1496 series