ZyXEL Communications U-1496 series Spezifikationen PDF herunterladen (Seite 15)

INSTALLATION AE/LZB 119 1889 R1A

To change the amount of time between each step in the

sequence, type set∧∧miscP,displayOffTime∧∧LX (replacing

X with the desired amount of time in milliseconds), and

press the Enter key (default is 500).

Bottom Line of Display

The bottom line of the SIM display is used to show the

messages shown in Table 3. To change the amount of time

each message is displayed if it is not replaced by another

message, type set∧∧miscP,displayPersistance∧∧LZ (replace

Z with the time in milliseconds), and press the Enter key

(default is 5000). Note that when two or more activities

occur in rapid succession, the messages may not be

displayed for the full amount of time.

To save the programming for the SIM display, do the

following:

1. Type run∧∧miscP,verifyAndLoad∧∧(∧∧) and press

the Enter key. The SIM should respond by

displaying the word OK.

2. Type run∧∧PersonalityObject,programFlash∧∧(∧∧)

and press the Enter key. The SIM should respond

by displaying the word OK.

Station GETC Communications

The default baud rate for BSL communications between

all GETCs and the SIM is 38,400 bps. If a “BSL Fail”

message is seen on the SIM display, the baud rates may not

be the same. To make sure that the BSL baud rate is set to

38,400 bps in the SIM, use the following procedure:

1. Press Ctrl + E to get the SIM to echo the typed

characters, so that you will be able to see (on the

screen of the PC or terminal) what you type.

2. Type set∧∧siteP,highSpeedBSL∧∧B1 and press the

Enter key.

3. Type run∧∧siteP,verifyAndLoad∧∧(∧∧)∧∧ and press

the Enter Key.

4. Type

run∧∧PersonalityObject,programFlash∧∧(∧∧)∧∧ and

press the Enter key.

5. Reset the SIM (push button in hole in front panel).

If it is necessary to set the BSL baud rate to 19,200 bps

in the SIM, use the same procedure but change step 2 as

follows:

2. Type set∧∧siteP,highSpeedBSL∧∧B0 and press the

Enter key.

When programming of the SIM is complete, disconnect

the programming cable from the SIM.

Table 3 - Messages for Bottom Line of Display

MESSAGE DESCRIPTION

BSL Fail No polling message has been received

by the SIM from the Control Channel

GETC for 15 seconds.

SMDisct The System Manager interface is

disconnected. If this message appears

every 15 to 30 seconds, the System

Manager cannot be contacted and

something must be wrong with the

System Manager connection.

GIDUpLod The System Manager has started a GID

upload to the site.

GID Done The GID upload to the site is complete.

MONMorse Morse Code ID was transmitted.

MONGrpCA Group Channel Assignment.

MONDtGCA Data Group Channel Assignment

MONDtICA Data Individual Channel Assignment

MONSpcCA Special Channel Assignment

MONIndCA Individual Channel Assignment

MONSyACA System All Call Channel Assignment

MONLgnAk Login Acknowledge

MONStsAk Status Ack

MONSysId System Id message

MONUnkey Radio Unkey

MONCanDR Cancel Dynamic Regroup

MONIniTC Initiate Test call

MONStatus Status Message

MONWCSID Working Channel System Assigned ID

MONLogin Radio Login

MONPage Paging channel assignment

MONConGC Confirmed Group Channel Assignment

MONConIC Confirmed Indiv Channel Assignment

MONCTISG Central Interconnect Group Channel

Assignment

MONSDrop Short Drop

MONCConf Channel confirmed

MONWCKey Working channel Key

MONWCUKy Working Channel unkey

MONWCDrp Working Channel drop

MONDpCar Drop with carrier

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 33 34

Kommentare zu diesen Handbüchern

Keine Kommentare

ZyXEL Communications U-1496 series Spezifikationen Seite 15

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung ZyXEL Communications U-1496 series