ZyXEL Communications VES-1012 - Betriebsanweisung Seite 118
- Seite / 227
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
VES-1000 Series Ethernet Switch
15-6 General, Switch and IP Setup
Figure 15-5 Menu 2.3 QoS Setup
Table 15-6 Menu 2.3 - QoS Setup
FIELD DESCRIPTION EXAMPLE
Priority
Level 7 to 0
Configure the priority-to-queue assignment for each port in this menu by
pressing [SPACE BAR] to select a queue (Queue 0 to Queue 3) and then
pressing [ENTER]. Queue 3 has the highest priority. Traffic assigned to higher
index queue gets through faster while traffic assigned to lower index queue is
dropped if the network is congested.
Queue 3
Once you have completed configuring Menu 2.2 — QoS Setup, press [ENTER] at the message “Press ENTER
to Confirm… “ to save your configuration or press [ESC] at any time to cancel.
15.3 TCP/IP Setup
From the main menu enter 1 to bring up Menu 3 – TCP/IP Setup.
15.3.1 TCP/IP Setup Parameters
The VES needs a static IP address for it to be managed over the network. The factory default IP address is
192.168.1.1. The administrator needs to assign a static IP address for the VES.
The subnet mask specifies the network number portion of an IP address. Your VES computes the subnet mask
automatically based on the IP address that you entered. You don’t need to change the subnet mask computed by the
VES unless you are instructed to do otherwise. The factory default subnet mask is 255.255.255.0.
The default gateway specifies the IP address of the default gateway (next hop) for outgoing traffic. The default
gateway is specified as 192.168.1.254.
Menu 2.3 - QoS Setup
Priority Queue Assignment
Priority Level 7= Queue 3
Priority Level 6= Queue 3
Priority Level 5= Queue 2
Priority Level 4= Queue 2
Priority Level 3= Queue 1
Priority Level 2= Queue 0
Priority Level 1= Queue 0
Priority Level 0= Queue 1
Press ENTER to Confirm or ESC to Cancel:
- VES-1000 Series 1
- Copyright 2
- FCC Interference Statement: 3
- FCC Warning! 3
- CE Mark Warning: 3
- Certifications 3
- ZyXEL Limited Warranty 4
- Customer Support 5
- Table of Contents 6
- List of Figures 10
- List of Figures xi 11
- List of Figures xiii 13
- List of Tables 14
- List of Tables xv 15
- Preface 17
- Part I: 19
- Chapter 1 21
- Getting to Know Your VES 21
- SNMP V1 (RFC 1157) 22
- Bridge MIB (RFC-1493) 22
- 1.3 Applications 23
- 1.3.2 Enterprise Application 24
- 1.3.3 Campus Application 25
- Chapter 2 27
- Hardware Connections 27
- 2.3 Front Panel 28
- 2.4 Front Panel Ports 28
- 2.4.1 Console Port 29
- 2.4.2 VDSL Port Connections 29
- 2.5 Front Panel LEDs 30
- Part II: 31
- Chapter 3 33
- 3.3 Home Screen 34
- 3.4 Screen Overview 35
- Chapter 4 39
- Initial Configuration 39
- 8. Click the Apply button 40
- Chapter 5 41
- Getting Started Screens 41
- 5.3 IGMP Snooping 42
- 5.4.2 How STP Works 43
- 5.5 GARP Timer 44
- 5.6 Switch Setup Screen 44
- Getting Started Screens 5-5 45
- Figure 5-3 Switch Setup 45
- DESCRIPTION 46
- Getting Started Screens 5-7 47
- Table 5-4 Switch Setup 47
- 5.7 IP Setup Screen 48
- Chapter 6 51
- 6.4 Rate Adaption 52
- 6.5 VDSL Default Values 52
- 6.6 GVRP 52
- 6.7 Port Setup Screen 53
- Port Setup 6-5 55
- 6-6 Port Setup 56
- Port Setup 6-7 57
- 6-8 Port Setup 58
- Figure 6-3 Uplink Port Setup 58
- Port Setup 6-9 59
- Table 6-5 Uplink Port Setup 59
- 6-10 Port Setup 60
- Chapter 7 61
- Static Route 61
- Static Route 7-3 63
- Table 7-2 Static Route Edit 63
- Chapter 8 65
- 8.5 VLAN Setup 67
- Part III: 73
- Chapter 9 75
- 9.1.1 Supported MIBs 76
- 9.1.2 SNMP Traps 76
- 9.1.3 Configuring SNMP 76
- Chapter 10 79
- Chapter 11 81
- LABEL DESCRIPTION 82
- Maintenance 11-3 83
- Table 11-1 Maintenance 83
- Chapter 12 89
- Statistics 89
- Statistics 12-3 91
- Table 12-2 Show STP Status 91
- Statistics 12-5 93
- Table 12-3 Hardware Monitor 93
- 12.2.5 Port Details Screen 96
- 12-10 Statistics 98
- Table 12-6 Port Details 98
- Statistics 12-11 99
- Chapter 13 101
- Diagnostic 101
- 13.4 Logout Screen 103
- Part IV: 105
- Chapter 14 107
- Introducing the SMT 107
- 14.5 SMT Menus At A Glance 108
- 14.5.1 Main Menu 109
- 14.6.1 Resetting the VES 111
- Chapter 15 113
- General, Switch and IP Setup 113
- 15.2.2 GARP Timer Setup 116
- 15.3 TCP/IP Setup 118
- Chapter 16 121
- Port Setup 121
- FIELD DESCRIPTION EXAMPLE 122
- JoeSoap 122
- 16.1.3 Ethernet Port Setup 123
- 16.2 Port Submenus 125
- Part V: 129
- Chapter 17 131
- Static Route Setup 131
- 17-2 Static Route Setup 132
- Chapter 18 133
- VLAN Setup 133
- 18.3 Port-Based VLAN Setup 135
- SYMBOL DESCRIPTION 136
- Chapter 19 137
- SNMP Configuration 137
- 19.2 Supported MIBs 138
- 19.3 Configuring SNMP 138
- 19.4 SNMP Traps 139
- 19-4 SNMP Configuration 140
- Table 19-3 SNMP Traps 140
- Part VI: 141
- Chapter 20 143
- System Maintenance 1 143
- 20.2.1 System Maintenance 144
- Port Statistics 145
- 20-4 System Maintenance 1 146
- Table 20-2 Port Statistics 146
- System Maintenance 1 20-5 147
- 20.2.3 VLAN Status 149
- 20.3.1 System Information 150
- 20.4 Log and Trace 151
- 20.4.1 Viewing Error Log 152
- 20.4.2 UNIX Syslog 152
- 20.5 Diagnostic 153
- Chapter 21 155
- Maintenance 155
- 21.2 Backup Configuration 156
- 21.2.4 GUI-based FTP Clients 157
- 21.2.7 TFTP Command Example 158
- 21.3 Restore Configuration 160
- 21.3.2 FTP Restore Example 161
- 21.4.1 Firmware File Upload 162
- 21.4.5 TFTP File Upload 164
- HyperTerminal 167
- Chapter 22 169
- System Maintenance 2 169
- 22.2.1 Resetting The Time 170
- 22.3.1 Secured Client Sets 171
- 22.4 Hardware Monitor 173
- Part VII: 177
- Chapter 23 179
- VDSL-Related Commands 179
- 23.2 VDSL Commands 180
- 23.2.1 Set VDSL Mode 181
- 23.2.4 Reset a VDSL Channel 182
- VDSL-Related Commands 23-5 183
- 23.2.7 VDSL Version Command 184
- 23.2.9 VDSL Show Command 184
- 23.2.11 VDSL Debug Command 185
- 23.3.4 Enet Fctrl Command 189
- 23.3.5 Enet Monitor Command 189
- Chapter 24 191
- Switch-Related Commands 191
- 24.3 Port Status Command 192
- 24.4 VLANs 193
- 24.4.1 VLAN Status Command 194
- 24.4.2 VLAN Set Command 195
- Sw vlan set 3 1 196
- Sw vlan set 4 1 196
- 24.4.3 VLAN Clear Command 198
- Sw vlan clear all 199
- 24.5 MAC Address Commands 200
- 24.6 MAC Address Learning 201
- 24.6.2 MAC Number 202
- 24.8 Switch Driver Commands 204
- TxFreeCnt = 79287 205
- Chapter 25 207
- IP Commands 207
- 25.1.2 IGMP Snooping Queries 208
- 25.1.3 Enable IGMP Snooping 209
- Chapter 26 211
- Troubleshooting 211
- 26.4 Data Rate 212
- 26.5 Configured Settings 212
- 26.6 Password 212
- 26.7 Remote Server 213
- 26.8 Telnet 213
- 26-4 Troubleshooting 214
- Part VIII: 215
- Appendix A 217
- Product Specifications 217
- Appendix B 219
- Pin Assignments 219
- B-2 Pin Assignments 220
- B-4 Pin Assignments 222
Verwandte Produkte und Handbücher für Vernetzung ZyXEL Communications VES-1012 -
(168 Seiten)
(12 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.144 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern